Contents | Index | Support | Knowledge Base | Software
|
|
Contents | Index | Support | Knowledge Base | Software |
|
|
|
|
|
|
|
|
This equipment complies with Part 68 of the FCC Rules. A label is attached to this equipment that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
This equipment uses the following USOC jacks: RJ-11C
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact 3Com Corporation at (800) NET3COM for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
No repairs may be done by the customer.
This equipment cannot be used on telephone company provided coin service. Connection to Party Line Service is subject to state tariffs.
When programming and/or making test calls to emergency numbers:
Remain on
the line and briefly explain to the dispatcher the reason for the call.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains, in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges).
In order to program this information into your facsimile, refer to your communications software user manual.
This equipment has been tested and found to comply with the limits for a Class B digital device as applicable, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Note: This card was tested to comply with FCC-15 Class B requirements in the cases of the following configurations:
MANUFACTURER'S DECLARATION OF CONFORMITY
Complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Note: This card was tested to comply with FCC-15 Class B requirements in the cases of the following configurations:
The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The load Number of this modem is .4. The standard connecting arrangement code for this equipment as specified in CP-01, Section 1.8.3 is CA11A.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe systems, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
This modem has been tested and certified according to the following safety standards and is intended for use only in Information Technology Equipment which has been tested and certified to these or other equivalent standards:
Marking
by the symbol 
indicates compliance of this equipment to the EMC Directive 89/336/EEC,
the Low Voltage Directive 73/23/EEC amended by 93/68/EEC and the
Telecom Terminal Equipment and Satellite Earth Stations Directive 98/13/EEC.
Such marking is indicative that this equipment meets or exceeds the
following technical standards:
EN 55022
- Limits and Methods of Measurement of Radio Interference
Characteristics of Information Technology Equipment.
WARNING: Although this equipment can use either loop disconnect (Pulse) or DTMF (Tone) signaling, only the performance of the DTMF signaling is certified for signaling to the PSTN. Pulse dial is available to users throughout Europe, but is only intended for signaling to private networks, such as PBXs. It is therefore strongly recommended that the equipment is set to use DTMF signaling for access to public or private emergency services. DTMF signaling also provides faster call set up.
This equipment has been approved to Council Decision 98/482/EEC--"CTR 21" for Pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, or itself, give an unconditional assurance of successful operation on every PSTN termination point. In the event of problems, you should contact your equipment supplier in the first instance.
This equipment has been designed to interwork with Public Switched Telephone Networks in the following countries in Europe:
Austria, Belguim, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
The safety status of the ports on this modem is as follows:
PCMCIA Bus connector to PC- SELV
Note that only SELV ports should be connected to other SELV ports or TNV ports to other TNV ports. Interconnection of ports with different safety status may invalidate the approval. If in doubt about making such a connection, advice should be sought from a competent engineer.
The user should ensure that the power drawn by the modem, together with the host and any auxiliary apparatus drawing power from the host is within the rating of the power supply.
The modem power requirement is: +5V @ 120 mA.
The user should be aware that it is the modem and not the host that is approved.
When the modem is supplied along with a host machine, the modem user instructions must also be supplied. Failure to do so will invalidate the modem approval.
Please consult the supplier or maintainer of the modem, not the network operator, if operational difficulties are experienced.
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
Not all phones connected to the phone port will respond to incoming ringing. Do not report this as a fault unless the same phone will not respond to ringing when connected to a standard phone socket.
This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Services.
The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular, higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
In addition to satisfactory line conditions a modem can only work properly if:
a) it is compatible with the modem at the other end of the call and,
b) the application using the modem is compatible with the application at the other end of the call - e.g. accessing the Internet requires suitable software in addition to a modem.
This equipment should not be used in a manner which could constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set up to operate within the following limits for compliance with Telecom specifications:
a) There shall be no more than 10 call attempts to the same number within any 30 minute period for a single manual call initiation
b) The equipment shall go back on-hook for a period of not less than 30 seconds between the end of one call attempt and the beginning of the next.
c) Automatic calls to different numbers shall be not less than 5 seconds apart.
d) When used in the Auto-Answer mode, the S0 register must be set with a value between 2 and 5. This ensures:
i. A person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.
ii. Caller identification information (which occurs between the first and second ring cadence) is not destroyed.
The code for Call Waiting disable is *52 on the Telecom New Zealand telephone network.
WARNING: Although this equipment can use either decadic (Pulse) or DTMF (Tone) signaling, only DTMF signaling is permitted when this modem is used on PSTN lines in Australia. Tone dialing provides faster call set up.
S-REGISTER DEFAULT PERMISSIBLE RANGE
CALL ATTEMPT/RETRIES: Applications software shall be configured so that not more than 3 attempts are made to establish a connection to a given number (Note: if the modem can detect service tones, up to 10 attempts can be made).
There must be at least 2 seconds between call attempts. If the call sequence is unsuccessful, there shall be a delay of at least 30 minutes before attempting to call the number again.
FACTORY DEFAULT SETTING: Use of the factory default settings will result in the modem being operated in a non-compliant manner. Please ensure that Australia is the chosen country from the country list prior to operation.
NOTE: Failure to set the modem, and any application software used with the modem, to the values shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment, and the Telecommunications Act 1991 prescribes a penalty of $12,000 for the connection of non permitted equipment in Australia.
