This equipment complies with Part 68 of the FCC Rules. A label is attached to this equipment that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
This equipment uses the following USOC jacks: RJ-11C
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact 3Com Corporation at (800) NET3COM for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.
WARNING: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
No repairs may be done by the customer.
This equipment cannot be used on telephone company provided coin service. Connection to Party Line Service is subject to state tariffs.
When programming and/or making test calls to emergency numbers:
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains, in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges).
In order to program this information into your facsimile, refer to your communications software user manual.
This equipment has been tested and found to comply with the limits for a Class B digital device as applicable, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product.
WARNING: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Note: This card was tested to comply with FCC-15 Class B requirements in the cases of the following configurations:
For Home or Office Use
3Com Corporation
605 North 5600 West
PO Box 16020
Salt Lake City, UT 84116
(800) 527-8677
Declares that the product:
Date: |
January 1999 |
Name: |
Megahertz |
Model Number: |
3CXM756, 3CCM756 |
Equipment Type: |
Modem |
Complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
|
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numéique de la classe B est conforme à la norme NMB-003 du Canada.
AVIS : L'étiquette d'Industrie Canada indique que le matériel est homologué. Cette homologation signifie que le matériel répond à certaines exigences de sécurité, de fonctionnement et de protection de réseau prescrites dans le(s) document(s) sur les exigences techniques relatives au matériel terminal. Le Ministère ne garantie nullement que le matériel fonctionnera à la satisfaction du client.
Avant d'installer ce matériel, l'utilisateur doit vérifier si le télécommunicateur en autorise la connexion à ses installations. Le matériel doit en outre être installé suivant une méthode acceptable de connexion. Le client doit être informé que la conformité aux conditions précités ne peut empêcher la dégradation du service dans certaines situations.
Les réparations au matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. Toutes réparations ou modifications effectuées par l'utilisateur sur le matériel, ou toutes défectuosités de celui-ci, peuvent motiver le télécommunicateur à demander à l'utilisateur de déconnecter le matériel.
Pour sa propre sécurité, l'utilisateur doit vérifier si les mises à la terre des circuits électriques, des lignes téléphoniques et des systèmes internes de plomberie métallique, s'il y a lieu, sont connectées ensemble. Cette précaution est particulièrement importante dans les régions rurales.
ATTENTION : L'utilisateur ne doit pas tenter d'effectuer lui-même de telles connexions ; il est recommandé de faire appel aux autorités d'inspection électrique appropriées ou à un électricien.
AVIS : Le numéro d'équivalence de sonnerie (REN) attribué à chaque équipement terminal fournit une indication du nombre maximum de matériel terminal pouvant être connecté à une interface téléphonique. Le raccordement à une interface peut consister en une combinaison quelconque d'appareils dans la mesure où la somme des numéros d'équivalence de sonnerie (REN) de tous les appareils ne dépasse pas 5.
Ce modem a été testé et homologué conformément aux normes de sécurité suivantes et il est destiné à être utilisé uniquement dans du matériel informatique testé et homologué selon ces mêmes normes ou des normes équivalentes :
La présence du symbole indique la conformité de ce matériel aux directives EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, amendée par 93/68/EEC, et Telecom Terminal Equipment and Satellite Earth Stations Directive 98/13/EEC. Ce symbole indique que ce matériel respecte et excède les normes techniques suivantes :
AVERTISSEMENT : Bien que cet équipement puisse utiliser la signalisation par ouverture de boucle ou la signalisation multifréquence en code 2, seules les performances de la signalisation multifréquence sont soumises à la réglementation sur le bon fonctionnement. Il est donc fortement recommandé que ce matériel soit réglé de manière à utiliser la signalisation multifréquence en code 2 pour accéder aux services d'urgence privés ou publiques. La signalisation multifréquence en code 2 assure en outre un établissement plus rapide des appels.
Ce matériel a été approuvé en vertu d'une décision du conseil 98/482/EEC--“ CTR 21 ” pour connexion terminale simple pan-européenne au réseau téléphonique public commuté (RTPC). Cependant, en raison des différences entre les RPTC des divers pays, cette approbation ne constitue pas une assurance inconditionnelle du bon fonctionnement du matériel à chacun des points de raccordement au RTPC. En cas de problèmes, communiquez d'abord avec le fournisseur du matériel.
L'état de sécurité des ports de ce modem est le suivant :
Port d'interface de ligne - TNV
Connecteur de bus PCMCIA au PC - SELV
Veuillez prendre note que seuls les ports SELV doivent être connectés à d'autres ports SELV ou les ports TNV à d'autres ports TNV. L'interconnexion de ports ayant un état de sécurité différent peut rendre l'approbation non valide. En cas de doute au sujet d'une telle connexion, demandez conseil à un ingénieur compétent.
L'utilisateur doit s'assurer que le courant utilisé par le modem, ainsi que par l'ordinateur hôte et tout autre appareil électrique, ne dépasse pas le calibre de l'alimentation électrique.
Besoins électriques du modem : +5V @ 350 mA.
L'utilisateur doit également être conscient que c'est le modem qui est approuvé et non l'ordinateur hôte.
Lorsque le modem est fourni avec un ordinateur, des instructions sur le modem destinées à l'utilisateur doivent également être fournies. Tout manquement à cet égard rend non valide l'approbation du modem.
Veuillez consulter le fournisseur ou la société responsable de la maintenance du modem, et non l'opérateur du réseau, en cas de problèmes fonctionnels.
Not all phones connected to the phone port will respond to incoming ringing. Do not report this as a fault unless the same phone will not respond to ringing when connected to a standard phone socket.
This equipment shall not be set up to make automatic calls to the Telecom 111 Emergency Services.
The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular, higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
In addition to satisfactory line conditions a modem can only work properly if:
a) it is compatible with the modem at the other end of the call and,
b) the application using the modem is compatible with the application at the other end of the call - e.g. accessing the Internet requires suitable software in addition to a modem.
This equipment should not be used in a manner which could constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set up to operate within the following limits for compliance with Telecom specifications:
a) There shall be no more than 10 call attempts to the same number within any 30 minute period for a single manual call initiation
b) The equipment shall go back on-hook for a period of not less than 30 seconds between the end of one call attempt and the beginning of the next.
c) Automatic calls to different numbers shall be not less than 5 seconds apart.
d) When used in the Auto-Answer mode, the S0 register must be set with a value between 2 and 5. This ensures:
i. A person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.
ii. Caller identification information (which occurs between the first and second ring cadence) is not destroyed.
The code for Call Waiting disable is *52 on the Telecom New Zealand telephone network.
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.