802.11g Wireless Turbo PC Card, PCI Adapter, PCI Adapter (with detachable antenna), and Access Point User Guide

Regulatory Information

FCC Declaration of Conformity
These devices comply with FCC Rules Part 15. Operation is subject to the following two conditions:
These devices may not cause harmful interference.
These devices must accept any interference received, including interference that may causeundesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If this equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Modifications to these devices not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Detachable Antenna Information
FCC Part 15, Subpart C, Section 15.203 Antenna requirement
USR 5416 and 5450 users: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

Industry Canada Statement
The term "IC" before the radio certification number only signifies that Industry Canada Technical specifications were met. This equipment complies with the Industry Canada Spectrum Management and Telecommunications policy, RSS-210 standard, Low Power License-Exempt Radio Communication Devices.

Operation is subject to the following two conditions:

This device may cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power(EIRP) is not more than required for successful communication. This device has been designed to operate with an antenna having a maximum gain of 2dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

UL Listing/CUL Listing

For external devices:
This information technology equipment is UL-Listed and CUL Listed for the uses described in the users guide.

For internal devices:
This information technology is UL-Listed and CUL-Listed for use with UL-Listed personal computers that have a users guide detailing user installation of card accessories.

CE Declaration of Conformity
We, USRobotics Corporation of 935 National Parkway, Schaumburg, Illinois, 60173-5157,USA, declare under our sole responsibility that the USRobotics 802.11g Wireless Turbo Multi-function Access Point, 802.11g Wireless Turbo PC Card, and 802.11g Wireless Turbo PCI Adapter, to which this declaration relates is in conformity with the following standards and/or other normative documents:
EN300 328-2
EN301 489-1
EN301 489-17
EN50371 (802.11g Wireless Turbo PC Card only)
EN60950

This equipment complies with Article 3.1(a) of Directive 1999/5/EC for the protection of the health and safety of the user.

We, USRobotics Corporation, hereby declare that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

This product can be used in the following countries:
Germany, Austria, Belgium, Switzerland, Netherlands, Luxembourg, Italy, France, UK, Ireland, Spain, Portugal, Sweden, Norway, Denmark, Finland, Iceland, and Greece

Regarding IEEE 802.11g we currently have the following information about restrictions in the R&TTE countries:

Country	frequency band	output power
France	2454-2483.5 MHz	10 mW EIRP outdoor

This device complies with the European requirements governing exposure to electromagnetic radiation. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This wireless device is a transmitter/receiver and has been designed and manufactured to comply with the exposure limits recommended by the Council of the European Union and the International Commission on Non-Ionizing Radiation Protection (ICNIRP, 1999) for the entire population. The exposure standard for portable equipment uses the "Specific Absorption Rate" as unit of measure. The maximum SAR value of this wireless device measured in the conformity test is 1.08 W/kg.

EU Detachable Antenna Information
This USR wireless device has been designed to operate with the antenna included in this package only. Together this device and antenna combination has been tested and approved by a European Agency conforming with the European R&TTE directive 1999/5/EC to meet the radiated power level requirement of 100mW e.i.r.p. Replacement of this antenna must only done with an authorized USR component that has been designed and tested with the unit to the requirements of directive 1999/5/EC. Please refer to the USR web site to get product antenna ordering information.

Operating Channels:

IEEE 802.11g compliant
11 channels (US, Canada)
13 channels (ETSI)
14 channels (Japan)

Go to www.usr.com to see the most recent channel restriction information.

Manufacturer's Disclaimer Statement

The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organisation of such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages. This document contains materials protected by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted in any form, by any means or for any purpose without expressed written consent of its authors. Product names appearing in this document are mentioned for identification purchases only. All trademarks, product names or brand names appearing in this document are registered property of their respective owners.

Contents:

802.11g Wireless Turbo PC Card, PCI Adapter, PCI Adapter (with detachable antenna), and Access Point User Guide

Regulatory Information