Step One: Connect Microfilter(s) (if included or required by your ISP)
A microfilter removes interference between voice and DSL signals. Your ISP will determine if a microfilter is necessary. If a microfilter was not included with the Wireless ADSL2+ Router, ask your ISP if one is needed.
Plug each telephony device cable (phone, fax machine, etc.) into the microfilter.
Plug the microfilter into the telephone wall jack.
Note: Do not install a microfilter on the cable that will connect your Wireless ADSL2+ Router to the telephone jack unless your microfilter has a connection for both the router and the phone.
Step Two: Connect your Wireless ADSL2+ Router to the Wall Phone Jack
Turn off your computer.
Connect one end of the included phone cable to the ADSL port on the router.
Connect the other end of the phone cable to a wall phone jack.
Step Three: Connect the router to Your Computer
Connect one end of the supplied Ethernet cable to your computer's Ethernet adapter.
Connect the other end to the LAN port on your router.
Step Four: Power Up the Network
Connect the supplied power adapter to the POWER port on the ADSL router.
Plug the power adapter into a standard power outlet.
Turn on your computer.
Step Five: Configure the Basic Connection Settings
Your Internet connection user name and password may be required for the installation of the Wireless ADSL2+ Router. Depending on your ISP, you may need to know some of the following information: IP Address, Subnet Mask, Gateway/Router, DNS Servers/Name Servers, and Service Name (optional).
Note: If you cannot find all the necessary information, contact your ISP for assistance in obtaining this information.
Start your Web browser.
In the location or address line, type: 192.168.2.1 and press ENTER
to access the Web User Interface.
If you are prompted to connect to the Internet, your web browser may prompt you to select Try Again or Connect.
Click LOGIN. There is no default password for the router.
Select your country and click Apply.
Verify you have selected the correct country and click OK.
In the Setup Wizard, click NEXT.
The Setup Wizard leads you through the basic router configuration process. If you are unsure about any connection information required by the wizard, contact your ISP.
For more information about the Setup Wizard's pages, see Setup Wizard.
Review all of the information.
If it is correct, click NEXT to complete the Setup Wizard.
If any of the information is not correct, click BACK to get to the appropriate screen, modify the information, then continue the Setup Wizard.
The information you supplied will be saved on the router and you will return to the main screen of the Web User Interface.
Note: If you did not set a Security Type and passphrase/key during the Setup Wizard, your wireless network is now open to wireless devices within operating range. To prevent access by unauthorized users, you must apply wireless security to the router.
Congratulations. You have successfully completed the installation procedure. Please register your USRobotics 9111 Wireless ADSL2+ Router at www.usr.com/productreg.
Connect a Wireless Device
For your wireless device to connect to the Wireless ADSL2+ Router, the wireless adapter for the device must have settings that match those of the router.
Ensure that each wireless adapter that will be connected to the network is set to infrastructure mode.
Set the SSID in the wireless adapter’s settings to the SSID that is used in the router. The router uses USR9111 as its default SSID.
If you set wireless security on the router, ensure that the security settings for the wireless adapter match those that you set on the Wireless ADSL2+ Router.
For instruction in changing your adapter’s wireless mode, see your wireless adapter’s documentation. If you purchased the USR5476 Wireless Starter Kit, see “Configuration” in the USR5423 USB Adapter User Guide.
Make a Backup of Your New Configuration Settings
Once you have your wireless router configured with your ISP information, USRobotics recommends you make a backup of your configuration settings.
From the Advanced Setup menu, select TOOLS > Configuration Tools.
Select Backup router configuration and click Next.
Your system will prompt you to save the file. Select Save.
Browse to the location at which you want the backup file saved and click Save.
