Contents:
Welcome to 56K Information Access
Installation for All Operating Systems
Technical Reference >
Introduction to Syntax and Procedures
Data Command Set
Result Codes
Result Codes
The modem responds to commands from the DTE and to activity on the line by signaling to the DTE in the form of result codes.
Two forms of each result code are available: long-form, an English-like "verbose" response, and short-form, a data-like numeric response (included in parentheses following the long-form). The long-form code is preceded and terminated by the sequence < CR> < LF>. The short-form is terminated by < CR>, only with no preceding sequence.
If result messages are suppressed, nothing is returned to the DTE. The long-form results codes can be modified by the OEM through the .INF file.
|
Code
|
Message
|
Meaning
|
| +F4 | +FCERROR | High speed fax data (V.27, V.29, V.33, or V.17) is expected but a V.21 signal is received. |
| 0 | OK | A command line has been executed. |
| 1 | CONNECT | For X command values specifying no speed reporting, the modem has connected to the line and either the line speed is 300 bps and line speed is enabled, or the DTE speed is 300 bps and DTE speed reporting is enabled. |
| 2 | RING | An incoming ring signal is detected on the line. What qualifies as a ring signal is determined by country-dependent parameters, modifiable through ConfigurACE. When cellular interface is selected, RING indicates that the cellular phone is receiving an receiving an incoming call. |
| 3 | NO CARRIER | Sent when attempting to establish a call if: 1. Ringback is detected and later ceases but no carrier is detected within the period of time determined by register S7, or 2. No ringback is detected within the period of time determined by register S7. Also sent when the modem auto-disconnects due to loss of carrier. For X0, sent for the following conditions: 1. If busy tone detection is enforced, busy or circuit busy has been detected. 2. If dial tone detection is enforced or selected, dial tone has not been detected. |
| 4 | ERROR | Sent during an attempt to execute a command line if any of the
following conditions occur: 1. The command line contains a syntax error. 2. The modem cannot execute a command contained in the command line, i.e., the command does not exist or is not supported. 3. A command parameter within the command line is outside the permitted range. For X0, X1, X2, and X3, this message is sent instead of DELAYED and BLACKLISTED. |
| 5 | CONNECT 1200 | The modem has connected to the line and either the line speed is 1200 bps and DCE speed reporting is enabled, or the DTE speed is 1200 bps and DTE speed reporting is enabled. |
| 6 | NO DIAL TONE | For X2 and X4, the modem has been instructed to wait for dial tone during dialing but none is received. When cellular phone interface is selected, indicates that cellular service is not currently available. |
| 7 | BUSY | For X3 and X4, if busy tone detection is enforced, the busy (engaged) signal is detected on the line when the modem is attempting to originate a call. |
| 8 | NO ANSWER | The modem is attempting to originate a call if a continuous ringback signal is detected on the line until the expiration of the timer S7. |
| 9 | CONNECT 600 | The modem has connected to the line, the DTE speed is 600 bps, and DTE speed reporting is enabled. |
| 10 | CONNECT 2400 | The modem has connected to the line and either the line speed is 2400 bps and DCE speed reporting is enabled, or the DTE speed is 2400 bps and DTE speed reporting is enabled. |
| 11 | CONNECT 4800 | The modem has connected to the line and either the line speed is 4800 bps and DCE speed reporting is enabled, or the DTE speed is 4800 bps and DTE speed reporting is enabled. |
| 12 | CONNECT 9600 | The modem has connected to the line and either the line speed is 9600 bps and DCE speed reporting is enabled, or the DTE speed is 9600 bps and DTE speed reporting is enabled. |
| 13 | CONNECT 6600 | The modem has connected to the line at 6600 bps and DCE speed reporting is enabled. |
| 14 | CONNECT 12000 | The modem has connected to the line at 12000 bps and DCE speed reporting is enabled. |
| 15 | CONNECT 14400 | The modem has connected to the line at 14400 bps and DCE speed reporting is enabled. |
| 16 | CONNECT 19200 | The modem has connected to the line and either the line speed is 19200 bps and DCE speed reporting is enabled, or the DTE speed is 19200 bps and DTE speed reporting is enabled. |
| 17 | CONNECT 38400 | The modem has connected to the line, the DTE speed is 38400 bps, and DTE speed reporting is enabled. |
| 18 | CONNECT 57600 | The modem has connected to the line, the DTE speed is 57600 bps, and DTE speed reporting is enabled. |
| 19 | CONNECT 115200 | The modem has connected to the line, the DTE speed is 115200 bps, and DTE speed reporting is enabled. |
| 20 | CONNECT 75TX/1200RX | The modem has established a V.23 originate connection and line speed reporting is enabled. |
| 23 | CONNECT 1200TX/75RX | The modem has established a V.23 answer connection and line speed reporting is enabled. |
| 24 | DELAYED | For X4, sent when a call fails to connect and the number dialed is considered 'delayed' due to country blacklisting requirements. |
| 32 | BACKLISTED | For X4, sent when a call fails to connect and the number dialed is considered 'blacklisted'. |
| 33 | FAX | A fax modem connection is established in a facsimile mode. |
| 35 | DATA | A data modem connection is established in a facsimile mode. |
| 40 | +MRR: 300 | The modem has connected to the line at 300 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 44 | +MRR: 1200/75 | The V.23 backward channel carrier is detected and carrier reporting is enabled. (See S95 and Xn.) |
| 45 | +MRR: 75/1200 | The V.23 forward channel carrier is detected and carrier reporting is enabled. (See S95 and Xn.) |
| 46 | +MRR: 1200 | The modem has connected to the line at 1200 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 47 | +MRR: 2400 | The modem has connected to the line at 2400 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 48 | +MRR: 4800 | The modem has connected to the line at 4800 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 49 | +MRR: 6600 | The modem has connected to the line at 6600 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 50 | +MRR: 9600 | The modem has connected to the line at 9600 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 51 | +MRR: 12000 | The modem has connected to the line at 12000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 52 | +MRR: 14400 | The modem has connected to the line at 14400 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 53 | +MRR: 16800 | The modem has connected to the line at 16800 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 54 | +MRR: 19200 | The modem has connected to the line at 19200 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 55 | +MRR: 21600 | The modem has connected to the line at 21600 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 56 | +MRR: 24000 | The modem has connected to the line at 24000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 57 | +MRR: 26400 | The modem has connected to the line at 26400 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 58 | +MRR: 28800 | The modem has connected to the line at 28800 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 59 | CONNECT 16800 | The modem has connected to the line, the DTE speed is 16800 bps and DTE speed reporting is enabled. |
| 61 | CONNECT 21600 | The modem has connected to the line, the DTE speed is 21600 bps and DTE speed reporting is enabled. |
| 62 | CONNECT 24000 | The modem has connected to the line, the DTE speed is 24000 bps and DTE speed reporting is enabled. |
| 63 | CONNECT 26400 | The modem has connected to the line, the DTE speed is 26400 bps and DTE speed reporting is enabled. |
| 64 | CONNECT 28800 | The modem has connected to the line and either the line speed is 28800 bps and DCE speed reporting is enabled, or the DTE speed is 28800 bps and DTE speed reporting is enabled. |
| 66 | +DR: ALT | The modem has connected to the line in MNP Class 5 and +DR: message reporting is enabled. (See S95, Wn, and Xn.) |
| 67 | +DR: V.42B | The modem has connected to the line in V.42 bis and +DR: message reporting is enabled. (See S95, Wn, and Xn.) |
| 69 | +DR: NONE | The modem has connected to the line without data compression and +DR: message reporting is enabled. (See S95, Wn, and Xn.) |
| 70 | +ER: NONE | The modem has connected to the line without any form of error correction and the +ER: message reporting has been enabled. (See S95, Wn, and Xn.) |
| 77 | +ER: LAPM | The modem has connected to the line in V.42 LAPM error correction mode and +ER: message reporting has been enabled. (See S95, Wn, and Xn.) |
| 78 | +MRR: 31200 | The modem has connected to the line at 31200 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 79 | +MRR: 33600 | The modem has connected to the line at 33600 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 80 | +ER: ALT | Sent when the modem has connected in the MNP mode of error correction, and +ER: message reporting has been enabled. (See S95, Wn, and Xn.) |
| 81 | +ER: ALT CELLULAR | The modem has connected in the MNP 10 mode and cellular power level adjustment is enabled (")M1 or )M2").(See S95, Wn, and Xn.) |
| 83 | LINE-IN-USE | The modem attempted to go off-hook when an extension was already occupying the line. |
| 84 | CONNECT 33600 | The modem has connected to the line, the DTE speed is 33600 bps and the DTE speed reporting is enabled. |
| 91 | CONNECT 31200 | The modem has connected to the line DTE speed is 31200 bps and the modem is to report the DTE speed upon connecting. |
| 134 | +MCR: B103 | The modem has connected to the line with Bell 103 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 135 | +MCR: B212 | The modem has connected to the line with Bell 212 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 136 | +MCR: V21 | The modem has connected to the line with ITU-T V.21 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 137 | +MCR: V22 | The modem has connected to the line with ITU-T V.22 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 138 | +MCR: V22B | The modem has connected to the line with ITU-T V.22 bis modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 139 | +MCR: V23 | The modem has connected to the line with ITU-T V.23 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 140 | +MCR: V32 | The modem has connected to the line with ITU-T V.32 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 141 | +MCR: V32B | The modem has connected to the line with ITU-T V.32 bis modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 142 | +MCR: V34 | The modem has connected to the line with ITU-T V.34 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 144 | +MCR: K56 | The modem has connected to the line with K56flex modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 145 | +MCR: V90 | The modem has connected to the line with ITU-T V.90 modulation and modulation reporting is enabled. (See +MR, S95 and Xn.) |
| 150 | +MRR: 32000 | The modem has connected to the line at 32000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 151 | +MRR: 34000 | The modem has connected to the line at 34000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 152 | +MRR: 36000 | The modem has connected to the line at 36000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 153 | +MRR: 38000 | The modem has connected to the line at 38000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 154 | +MRR: 40000 | The modem has connected to the line at 40000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 155 | +MRR: 42000 | The modem has connected to the line at 42000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 156 | +MRR: 44000 | The modem has connected to the line at 44000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 157 | +MRR: 46000 | The modem has connected to the line at 46000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 158 | +MRR: 48000 | The modem has connected to the line at 48000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 159 | +MRR: 50000 | The modem has connected to the line at 50000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 160 | +MRR: 52000 | The modem has connected to the line at 52000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 161 | +MRR: 54000 | The modem has connected to the line at 54000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 162 | +MRR: 56000 | The modem has connected to the line at 56000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 165 | CONNECT 32000 | The modem has connected to the line at 32000 bps and DCE speed reporting is enabled. |
| 166 | CONNECT 34000 | The modem has connected to the line at 34000 bps and DCE speed reporting is enabled. |
| 167 | CONNECT 36000 | The modem has connected to the line at 36000 bps and DCE speed reporting is enabled. |
| 168 | CONNECT 38000 | The modem has connected to the line at 38000 bps and DCE speed reporting is enabled. |
| 169 | CONNECT 40000 | The modem has connected to the line at 40000 bps and DCE speed reporting is enabled. |
| 170 | CONNECT 42000 | The modem has connected to the line at 42000 bps and DCE speed reporting is enabled. |
| 171 | CONNECT 44000 | The modem has connected to the line at 44000 bps and DCE speed reporting is enabled. |
| 172 | CONNECT 46000 | The modem has connected to the line at 46000 bps and DCE speed reporting is enabled. |
| 173 | CONNECT 48000 | The modem has connected to the line at 48000 bps and DCE speed reporting is enabled. |
| 174 | CONNECT 50000 | The modem has connected to the line at 50000 bps and DCE speed reporting is enabled. |
| 175 | CONNECT 52000 | The modem has connected to the line at 52000 bps and DCE speed reporting is enabled. |
| 176 | CONNECT 54000 | The modem has connected to the line at 54000 bps and DCE speed reporting is enabled. |
| 177 | CONNECT 56000 | The modem has connected to the line at 56000 bps and DCE speed reporting is enabled. |
| 178 | CONNECT 230400 | The modem has connected to the line, the DTE speed is 230400 bps, and DTE speed reporting is enabled. |
| 180 | CONNECT 28000 | The modem has connected to the line at 28000 bps and DCE SPEED reporting is enabled. |
| 181 | CONNECT 29333 | The modem has connected to the line at 29333 bps and DCE SPEED reporting is enabled. |
| 182 | CONNECT 30667 | The modem has connected to the line at 30667 bps and DCE SPEED reporting is enabled. |
| 183 | CONNECT 33333 | The modem has connected to the line at 33333 bps and DCE SPEED reporting is enabled. |
| 184 | CONNECT 34667 | The modem has connected to the line at 34667 bps and DCE SPEED reporting is enabled. |
| 185 | CONNECT 37333 | The modem has connected to the line at 37333 bps and DCE SPEED reporting is enabled. |
| 186 | CONNECT 38667 | The modem has connected to the line at 38667 bps and DCE SPEED reporting is enabled. |
| 187 | CONNECT 41333 | The modem has connected to the line at 41333 bps and DCE SPEED reporting is enabled. |
| 188 | CONNECT 42667 | The modem has connected to the line at 42667 bps and DCE SPEED reporting is enabled. |
| 189 | CONNECT 45333 | The modem has connected to the line at 45333 bps and DCE SPEED reporting is enabled. |
| 190 | CONNECT 46667 | The modem has connected to the line at 46667 bps and DCE SPEED reporting is enabled. |
| 191 | CONNECT 49333 | The modem has connected to the line at 49333 bps and DCE SPEED reporting is enabled. |
| 192 | CONNECT 50667 | The modem has connected to the line at 50667 bps and DCE SPEED reporting is enabled. |
| 193 | CONNECT 53333 | The modem has connected to the line at 53333 bps and DCE SPEED reporting is enabled. |
| 194 | CONNECT 54667 | The modem has connected to the line at 54667 bps and DCE SPEED reporting is enabled. |
| 195 | +MRR: 28000 | The modem has connected to the line at 28000 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 196 | +MRR: 29333 | The modem has connected to the line at 29333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 197 | +MRR: 30667 | The modem has connected to the line at 30667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 198 | +MRR: 33333 | The modem has connected to the line at 33333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 199 | +MRR: 34667 | The modem has connected to the line at 34667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 200 | +MRR: 37333 | The modem has connected to the line at 37333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 201 | +MRR: 38667 | The modem has connected to the line at 38667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 202 | +MRR: 41333 | The modem has connected to the line at 41333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 203 | +MRR: 42667 | The modem has connected to the line at 42667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 204 | +MRR: 45333 | The modem has connected to the line at 45333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 205 | +MRR: 46667 | The modem has connected to the line at 46667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 206 | +MRR: 49333 | The modem has connected to the line at 49333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 207 | +MRR: 50667 | The modem has connected to the line at 50667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 208 | +MRR: 53333 | The modem has connected to the line at 53333 bps and carrier reporting is enabled. (See S95 and Xn.) |
| 209 | +MRR: 54667 | The modem has connected to the line at 54667 bps and carrier reporting is enabled. (See S95 and Xn.) |
| Notes:
1. See Vn for result code selection, i.e., short form (result code) or verbose/extended (result message). 2. See Wn for extended connect message control. 3. See S95 for extended result code enabling options (which override some Wn commands). 4. See Xn for extended result code subset enabling options. 5. See \Vn for single line connect message enable options. 6. See +MR for modulation reporting control. |
||
