802.11g Wireless Turbo PC Card and PCI Adapter User Guide
Troubleshooting and Support
I accidentally clicked Cancel during
the installation procedure for the 802.11g Wireless Turbo PC Card or PCI
Adapter.
Possible Solution:
Remove and reinsert the USRobotics Installation CD-ROM into your CD-ROM
drive. Repeat the installation procedure of the software before you install
any hardware.
The installation procedure did not
begin when I inserted the Installation CD-ROM.
Possible Solution:
Some programs may keep the autolaunch feature of the Installation CD-ROM
from beginning. Close any open applications and reinsert the Installation
CD-ROM. If the Installation CD-ROM interface does not run automatically,
click Windows Start and then click Run. In the Run
dialog box, type D:\setup.exe. If your CD-ROM drive uses a different
letter, type that letter in place of D.
The 802.11g Wireless Turbo PC Card
or PCI Adapter cannot communicate with other computers linked via Wireless
in the Infrastructure configuration.
Possible Solution:
- Ensure that each computer in the wireless network is powered on.
- Ensure that each 802.11g Wireless Turbo PC Card is configured on the
same SSID, same level of WEP encryption, and same WEP key. If the SSIDs
and levels of WEP encryption are different, change each 802.11g Wireless
Turbo PC Card within the LAN to the same SSID, same level of WEP encryption,
and same WEP key.
- Ensure TCP/IP is installed. Ensure you are a part of the same domain
or workgroup. Ensure that you are automatically obtaining the IP address
or that you have a correct IP address and subnet mask. Reset the Wireless
Access Point and restart the computer that has a connectivity issue.
- Ensure that you have some files available for sharing.
My computer does not recognise the
802.11g Wireless Turbo PC Card or PCI Adapter.
Possible Solution:
Laptop users:
- The 802.11g Wireless Turbo PC Card may not be fully inserted into
the PC Card slot.
Desktop users:
- The 802.11g Wireless Turbo PCI Adapter may not be fully inserted into
the PCI slot. You can also try installing the 802.11g Wireless Turbo
PCI Adapter into a different PCI slot.
- Your PCI slot may not be configured correctly. To configure your PCI
slot, contact your computer manufacturer.
I am unable to communicate
with an Access Point or Wireless Router using my 802.11g Wireless Turbo
PC Card or PCI Adapter.
Possible Solution:
Be sure that each 802.11g Wireless Turbo PC Card that you want to connect
to the wireless network is set to Infrastructure mode within the Configuration
Utility. If your 802.11g Wireless Turbo PC Cards are not set to Infrastructure
mode, they will not be able to communicate with an Access Point or Wireless
Router.
Possible Solution:
Ensure that you are contacting the correct Access Point by verifying the
MAC address.
Possible Solution:
Ensure that the correct Authentication Mode and WEP encryption key are
being used. If you changed the settings in the configuration of the Access
Point, you must also change the settings of every 802.11g Wireless Turbo
PC Card attached to this network. The settings of the 802.11g Wireless
Turbo PC Cards must match the new settings of the Access Point. If you
are still experiencing difficulties, reset all of your Wireless Access
Points and wireless network adapters to the default settings and try again.
Possible Solution:
Ensure that you can connect to the Wireless Access Point and that the
BSSID shows the MAC address of the Access Point you want to communicate
with.
Possible Solution:
Ensure that the Wireless Configuration Utility is installed for your 802.11g
Wireless Turbo PC Card and that the Wireless Configuration Utility detects
your 802.11g Wireless Turbo PC Card.
Possible Solution:
If you are not using a USRobotics Wireless Access Point, ensure that
you can connect to the Access Point and that the preamble mode is set
correctly. The default setting for USRobotics products is Long.
I am unable to establish a
wireless connection with my 802.11g Wireless Turbo PC Card.
Possible Solution:
Verify that the 802.11g Wireless Turbo PC Card is properly installed.
If you continue to experience problems, uninstall the 802.11g Wireless
Turbo PC Card and repeat the installation procedure.
Possible Solution:
If you are attempting a peer-to-peer connection, verify that each wireless
adapter is set to 802.11 Adhoc mode. If you are using a Wireless Access
Point, verify that each wireless adapter is set to Infrastructure mode.
My 802.11g Wireless Turbo
PC Card does not see my Access Point in the list when I scan for it.
Possible Solution:
If you create a wireless connection with the 802.11g Wireless Turbo PC
Card but are experiencing poor link quality, check the positioning of
the 802.11g Wireless Turbo PC Card. Long distances, multiple floors, or
steel or concrete walls can diminish the link quality. If possible, reposition
the 802.11g Wireless Turbo PC Card to reduce the effect of any of these
obstacles. In addition, check any physical connections between the Access
Point and your modem, router, hub, LAN, or switch.
Possible Solution:
If your Access Point is not broadcasting an SSID, it will not appear during
a scan by your 802.11g Wireless Turbo PC Card. The client will need to
be manually configured.
Are You Still Having Problems?
1. Go to the USRobotics Web site at www.usr.com.
Many of the most common difficulties users experience have been addressed
in the FAQ and Troubleshooting Web pages for your specific product.
2. Call the USRobotics Technical Support Department.
Technical questions about USRobotics products can also be answered
by technical support specialists.
To obtain the most current support information, including procedures to
obtain Service Repair Orders, visit the U.S.Robotics Web site: http://www.usr.com.
= USRobotics has thoroughly tested this driver with
the supported hardware and has verified compatibility with Windows 2000.
Because USRobotics wants its customers to take full advantage of the
product's functionality, we made the driver available.
|