USRobotics
       

Contents:

Introduction

Hardware Installation

Configuring the Wireless Cable/DSL Router

Print Server

Troubleshooting

Appendices >

Regulatory Information

Frequently Asked Questions

USRobotics Corporation Limited Warranty

Wireless Cable/DSL Router User Guide (Windows 95, 98, 2000, NT, Me, XP, and Macintosh)

Appendices

Appendix A

Appendix B

Appendix A

Cable or DSL Connection

This User Guide covers most Cable and DSL installations that are configured for Dynamic or Static IP addressing. This guide assumes that you have active and properly functioning Cable or DSL Internet service.

Note: DSL users, if you use a login application to access the Internet, you are more than likely using a PPPoE connection. Refer to the appropriate section in this User Guide for information on collecting your configuration information. If you use Dial-Up Networking and a VPN adapter, you are most likely using a PPTP connection. Refer to the appropriate section of this User Guide for information on collecting your configuration information. If you are unsure about what type of connection you are using, contact your Internet Service Provider.

Note: Your Cable or DSL modem must be connected to your computer via an RJ-45 Ethernet connection. The Wireless Cable/DSL Router is not compatible with Cable or DSL modems with only a USB connection. You must have an Ethernet adapter (NIC) or 802.11b Wireless Adapter installed in your computer.

You need to gather the following information about your computer from your Internet Service Provider (ISP). Contact your ISP for assistance in obtaining this information.

IP Address:
_______________-_______________-_______________-_______________
Subnet Mask:
_______________-_______________-_______________-_______________
Gateway/Router:
_______________-_______________-_______________-_______________
DNS Servers/
Name Servers:


_______________-_______________-_______________-_______________

_______________-_______________-_______________-_______________

Host Name/ DHCP Client ID:


______________________________________________________________

Not all of this information may be required for the installation of the Wireless Cable/DSL Router. If your ISP cannot provide you with this information, the following basic steps will assist you in gathering most of the required information.

A. You need to perform these steps on the computer that is currently connected to your Cable or DSL modem.

Windows Users

  1. All Windows Users:
    Click Windows Start, Settings, and then Control Panel.

  2. Windows 95/98/Me Users:
    Double-click Network.

    Windows 2000 and XP Users:
    Double-click Network and Dial-up Connections.

    Windows NT Users:
    Double-click Network and then click the Protocols tab.

  3. All Windows Users:
    Select the TCP/IP option for the network adapter that is used to connect to your Cable or DSL modem and click Properties. Proceed to Step B.

Macintosh Users

Macintosh OS 9.x Users:
Click Apple, Control Panels and then TCP/IP. Proceed to Step B.

Macintosh OS X Users:
Click Apple, System Preferences and then Network. Proceed to Step B.

B. All Windows Users:
You should now be in the TCP/IP Properties window.

  • If the Obtain an IP address automatically option is selected, you may proceed with the installation of the Wireless Cable/DSL Router in the “Connecting a cable or DSL modem to the Wireless Cable/DSL Router” section of this Guide.
  • If this option is not selected, you will need to collect the necessary configuration information if it was not provided by your Service Provider. Depending on your operating system, you may need to click multiple tabs within the TCP/IP window to obtain all the necessary information. Once completed, select the Obtain an IP address automatically option and click OK. If necessary, click OK again to close the Network Properties page. If you are prompted to restart your computer, click No. You may proceed to the “Connecting a cable or DSL modem to the Wireless Cable/DSL Router” section of this Guide.

All Macintosh Users:
Change the Connect via: option from whatever it is currently at to Connect via: Ethernet.

Check to see what the Configure: option is set to and if any information is supplied by your service provider for the IP address, DHCP Client ID, or Name Servers.

  • If the Configure: option is set to Using DHCP, you may proceed to the “Connecting a cable or DSL modem to the Wireless Cable/DSL Router” section of this Guide.

  • If the Configure: option is not set to Using DHCP, you will need to collect the necessary configuration information if it was not provided by your Service Provider. You may need to click multiple tabs within the TCP/IP or Network window to obtain all the necessary information. Set the TCP/IP Configure: option to Using DHCP. Click Save and close the TCP/IP or Network window. You may proceed to the “Connecting a cable or DSL modem to the Wireless Cable/DSL Router” section of this Guide.


PPPoE connection

This User Guide covers most Cable and DSL installations that are configured for Dynamic or Static IP addressing. This guide assumes that you have an active and properly functioning Cable or DSL Internet service.

Note: DSL users, if you use a login application to access the Internet, you are more than likely using a PPPoE connection. If you are unsure about what type of connection you are using, contact your Internet Service Provider.

You will be required to gather the following information about your computer from your Internet Service Provider. To obtain the necessary information, first look within your login application. If you cannot find all the necessary information, contact your Service Provider for assistance in obtaining this information.

IP Address:
_______________-_______________-_______________-_______________
Subnet Mask:
_______________-_______________-_______________-_______________
Gateway/Router:
_______________-_______________-_______________-_______________
DNS Servers/
Name Servers:


_______________-_______________-_______________-_______________

_______________-_______________-_______________-_______________

User Name:
______________________________________________________________
Password:
______________________________________________________________
Service Name (optional):


______________________________________________________________

Not all of this information may be required for the installation of the Wireless Cable/DSL Router.


PPTP connection

Note: If you use Dial-Up Networking and a VPN adapter, you are most likely using a PPTP connection. If you are unsure about what type of connection you are using, contact your Internet Service Provider.

You will be required to gather the following information about your computer from your Internet Service Provider. To obtain the necessary information, first look within your login application. If you cannot find all the necessary information, contact your Service Provider for assistance in obtaining this information.

PPTP Account (User Name):
______________________________________________________________
PPTP Password:
______________________________________________________________
Service Name:
______________________________________________________________
IP Address:
_______________-_______________-_______________-_______________
Subnet Mask:
_______________-_______________-_______________-_______________
Server IP address:
_______________-_______________-_______________-_______________
Connection ID:


______________________________________________________________

Not all of this information may be required for the installation of the Wireless Cable/DSL Router.


Appendix B

Analogue or ISDN connection

This User Guide covers most dial-up or remote access connections that are configured for Dynamic or Static IP addressing. This guide assumes that you have an active and properly functioning analogue or ISDN Internet service.

Note: The Wireless Cable/DSL Router requires an external analogue or ISDN modem for dial-up functionality. Your analogue or ISDN modem must be connected to your computer via an RS-232 serial connection. The Wireless Cable/DSL Router is not compatible with analogue or ISDN modems with only a USB connection. You must have an Ethernet adapter (NIC) or 802.11b Wireless Adapter installed in your computer.

You need to gather the following information about your Dial-up or Remote Access connection to your Internet Service Provider (ISP). Contact your ISP for assistance in obtaining this information.

 

IP Address:
_______________-_______________-_______________-_______________
Subnet Mask:
_______________-_______________-_______________-_______________
Gateway/Router:
_______________-_______________-_______________-_______________
DNS Servers/
Name Servers:


_______________-_______________-_______________-_______________

_______________-_______________-_______________-_______________

User Name:
______________________________________________________________
Password:
______________________________________________________________
Dial-up Access Number:


______________________________________________________________

*If you are using Windows, go to your Dial-up Networking or Network and Dial-up Connections folder to get this information. If you are using a Macintosh, enter Remote Access through Control Panels to get this information.

Not all of this information may be required for the installation of the Wireless Cable/DSL Router. If your ISP cannot provide you with this information, the following basic steps will assist you in gathering most of the required information.

A. You need to perform these steps on the computer that is currently connected to your analogue or ISDN modem.

Windows 95 and 98 Users:
Right-click My Computer and then click Explore. Double-click Dial-Up Networking. Right-click your ISP connection and click Properties. Click the Server Types tab and then click the TCP/IP Settings button. Proceed to Step B.

Windows 2000 Users:
Click Windows Start, Settings, and then Control Panel. Double-click Network and Dial-up Connections. Right-click your ISP connection and click Properties. Click the Networking tab and then scroll down in the list of components. Select Internet Protocol (TCP/IP) and click Properties. Proceed to Step B.

Windows NT Users:
Right-click My Computer and then click Explore. Double-click Dial-Up Networking. Select your ISP connection from the Phonebook entry drop-down menu. Click More and select Edit entry and modem properties. Click the Server tab and then click the TCP/IP Settings button. Proceed to Step B.

Windows Me Users:
Click Windows Start, Settings, and then Dial-Up Networking. Right-click your ISP connection and click Properties. Click the Networking tab and then click the TCP/IP Settings button. Proceed to Step B.

Windows XP Users:
Click Windows Start and then Control Panel. Double-click Network Connections. Right-click your ISP connection and click Properties. Click the Networking tab, select Internet Protocol (TCP/IP) from the menu, and click Properties. Proceed to Step B.

Macintosh OS 9.x Users:
Click Apple, Control Panels, and then TCP/IP. Proceed to Step B.

Macintosh OS X Users:
Click Apple, System Preferences, and then Network. Proceed to Step B.

B. All Windows Users:
You should now be in the TCP/IP Properties window.

If the Server assigned IP address and Server assigned name server addresses options are selected, you have a Dynamic IP address. Close any open Properties windows and proceed to the “Connecting an Analogue or ISDN modem to the Wireless Cable/DSL Router” section in this Guide.

If these options are not selected, you have a Static IP address and will need to check for the following information: IP Address, Subnet Mask, and Default Gateway. You may proceed to the “Connecting an Analogue or ISDN modem to the Wireless Cable/DSL Router” section in this Guide.

All Macintosh Users:

  • If the Configure: option is set to Manually, write any of the supplied information in the previous table. Set the Configure: option to Using DHCP Server.

  • If the Configure: option is set to any other selection, change it to Using DHCP Server.

Change the Connect via: option from whatever it is currently at to Connect via: Ethernet.

Click Save and close the TCP/IP or network window. You may proceed to the “Connecting an Analogue or ISDN modem to the Wireless Cable/DSL Router” section in this Guide.